Ubiquiti UniFi Firmware Release Notes: 3.9.24.8264

Official Release Notes

You can find official release notes from Ubiquiti here:

HD/SHD/XG

  • 3.9.24-3.9.27.8537
    • Fixed an issue with the reported uplink interface after RF scan when bonding was enabled.
    • Fixed 802.1X VLAN reporting when RADIUS VLAN was enabled.
    • Increased NTP client update frequency.
    • Improved client STA performance for SSIDs with DVLAN enabled.
    • Removed unnecessary logging.
    • SHD/XG Only
      • Fixed a performance issue.
    • XG Only
      • Re-enabled autonegotiation on the 10 GbE PHY.
  •  3.9.21-3.9.24.8264
    • Improved device stability when using rate control.
    • Fixed channel utilization stats.
    • Fixed spectral scanning support.
    • Fixed forwarding of fragmented IPv6 packets.
    • SHD/XG Only
  • 3.9.19-3.9.21.8191
    • Fixed the speed regression introduced in 3.9.18.
    • Made an improvement to stability.
    • XG Only
      • 10Gbps Ethernet performance Improvements.
  • 3.9.18-3.9.19.8123
    • Fixed a memory leak when multicast enhancements were enabled.
  • 3.9.15-3.9.18.8086
    • Made improvements to stability and performance.
  • 3.9.3/3.9.6-3.9.15.8011
    • XG Only
    • USXG Only
      • Improved LAG config handling.

nanoHD

  • 3.9.24-3.9.27.8537
    • Added:
      • Channel utilization counters.
      • DTIM Support.
      • Initial Bandsteering support.
      • athstats tool.
      • Broadcast filtering support.
    • Enabled DFS support.
    • Fixed:
      • broadcast filter configuration.
      • hidden SSID support.
      • crash triggered by provisioning.
      • bug causing SNMP hostname to disappear after provision and reboot.
      • PMF support.
  •  3.9.21-3.9.24.8264
    • Added channel utilization support (currently 5GHz only).
    • Enabled VHT160 support.
    • Added nslookup.
    • Enabled MU-MIMO.
    • Fixed per-STA rate limiting support (user groups).
    • Stopped broadcasting default SSID.
    • Added MAC ACL support.
    • Fixed RADIUS VLAN support.
    • Fixed fast-apply support.
    • Fixed HT40 support on 2.4GHz.
    • Made improvements to stability.
  •  3.9.19-3.9.21.8191
    • Merged 3rd release firmware.
    • Added RADIUS VLAN support.
    • Added fast-apply support.
    • Added 802.11w support (PMF).
    • Added 802.11X identity support.
    • Disabled country code IE.
    • Made improvements to stability.
  • 3.9.18-3.9.19.8123
    • Fixed MBSS support.
    • Made improvements to stability.
  • 3.9.15-3.9.18.8086
    • Added guest control support.
    • Added 802.1X support.
    • Added support for multiple BSSIDs per radio.
    • Fixed issue when using a bracket in the ESSID or PSK.
    • Fixed auto channel selection issue.
    • Fixed 802.11n negotiation issue.
    • Fixed issue which could cause Ethernet to stay down after provision or reboot.
  • 3.9.3/3.9.6-3.9.15.8011
    • Added stainfo support.

UAP

  • 3.9.24-3.9.27.8537
    • Disabled over the DS fast BSS transition.
    • Fixed management VLANs on downlink UAPs.
    • Fixed a bug which sometimes caused 100% CPU usage when fast BSS transition was enabled.
    • Made various wireless uplink changes, including adding multi-radio uplink support.
    • Now track MAC filter rejections.
    • UAPG3 Only
      • Fixed remaining crash when 802.11r is enabled.
      • Reverted a patch which disabled the secondary ethernet when using wireless uplinks.
    • UAPG2/G3 Only
      • Improved channel utilization reporting accuracy.
    • UAPG2
      • Made improvements to performance.
    • UAP-Pro Only
      • Removed bandsteering as it isn’t supported.
  •  3.9.21-3.9.24.8264
    • Refactored and improved fast-apply, which also fixed two small memory leaks.
  •  3.9.19-3.9.21.8191
    • Fixed a memory leak related to the redirector.
    • UAPG2/G3 Only
    • UAPG1 Only
      • Fixed device firmware upgrade.
  • 3.9.18-3.9.19.8123
    • Fixed NAS-IP-Address attribute so that it always returns the management IP of the AP.
  • 3.9.15-3.9.18.8086
    • Improved STA signal reporting
    • Made improvements to wireless uplink/mesh V3.
    • Fixed a bug with rate control when using multiple SSIDs.
  • 3.9.3/3.9.6-3.9.15.8011
    • Fixed a small memory leak.
    • Fixed outdoor flag.
    • Added fast-apply for guest portal.
    • Improved guest portal redirector handling.
    • Fixed a bug with L3 wireless adoption.
    • Fixed bandsteering.
    • Fixed issue with bridge priority so the secondary ethernet port remains enabled.
    • Improved DFS.
    • Fixed an issue preventing bandsteering from being enabled.
    • Fixed an issue with the downlink monitor.
    • Added uplink priority for the bridge interfaces.
    • Added KRACK AP mode patches for 802.11r.
    • UAPG3 Only
      • Fixed minimum rates.
      • Further improvements to device upgrade and boot times.
      • Fixed a crash in hostapd when Fast Roaming is enabled.
      • Added support for 82.11r and 802.11k.
      • Fixed channel utilization reports.
      • Improvement bootup and TFP recovery times.
    • UAPG2/G3 Only
      • Added RADIUS VLAN support to MAC authentication bypass.
      • Fixed a bug which prevented APs from uprgading when bandsteering was neabled.
      • Fxied issue with 3.9.3.7537 which caused some APs to not accept any clients.
    • UAPG2 Only
      • Added support for 802.11k.
    • UAPG1/G2
      • Added net-snmp.

HW

  • 3.9.24-3.9.27.8537
    • Made L3 adoption and management improvements.
  •  3.9.21-3.9.24.8264
    • Added device hostname in shell.
    • Optimized image size.
  •  3.9.19-3.9.21.8191
    • Enabled TCP Packetization-Layer Path MTU Discovery when an ICMP black hole is detected.
    • Improved CPU utilization of SNMP.
  • 3.9.18-3.9.19.8123
    • Fixed some issues which would cause L3 adopted devices to show up as disconnected in the controller.
    • Fixed SNMP sysName.
  • 3.9.15-3.9.18.8086
    • New protocol implementation.
    • Added controller support for netconsole.
  • 3.9.3-3.9.15.8011
    • Improved security.
    • Updated openssl package to 1.0.2m.
    • Updated curl to 7.57.0.
    • Added IPv6 management support.
    • Improved event notification on device upgrade.

USW

  • 3.9.21-3.9.27.8537
    • Fixed crash caused by autodetect.
    • Adjusted MAB priority, no longer waiting for 802.1X timeout to process.
    • Fixed port mirroring provisioning.
    • Added switch PoE port overload and disconnect reporting.
  •  3.9.19-3.9.21.8191
    • Enhanced DHCP snooping trace log for LAGs
  • 3.9.15-3.9.18.8086
    • Made various improvements.
  • 3.9.3/3.9.6-3.9.15.8011
    • Added port ID in STP error message.
    • Lowered STP topology change log level.
    • Improved DHCP guarding and snooping.
    • Added DHCP snooping debug command.

USL2

  • 3.9.3/3.9.6-3.9.15.8011
    • Improved PSU status reporting.

AC-IW/IW-Pro/EDU/M-Pro

  • 3.9.3/3.9.6-3.9.15.8011
    • Fixed VLAN pass-through regression
    • Added port disable support.
    • AC-IW/IW-Pro Only
      • Improved VLAN config and prevented traffic leaks.
      • Fixed RADIUS VLAN when port VLAN is enabled.
      • Added QoS CIR/EIR support.
      • Made improvements to performance.
      • Fixed management VLAN issue causing decreased multicast performance.
    • EDU only

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

%d bloggers like this: